Author Topic: Distance of Print Below Collar  (Read 1387 times)

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13945
  • Docendo discimus
Distance of Print Below Collar
« on: February 22, 2018, 04:21:13 PM »
Not quite worthy of a poll, but when giving, or when being given a position measurement "below the collar", is it from the opening, or the ribbed collar itself?
That rug really tied the room together, did it not?


Offline Croft

  • Hero Member
  • *****
  • Posts: 875
Re: Distance of Print Below Collar
« Reply #1 on: February 22, 2018, 04:36:02 PM »
Not quite worthy of a poll, but when giving, or when being given a position measurement "below the collar", is it from the opening, or the ribbed collar itself?

the majority I do are just past the end of a typical gildan label , so i don't have to mess around getting it out of the way so 1.5" down from seam

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13945
  • Docendo discimus
Re: Distance of Print Below Collar
« Reply #2 on: February 22, 2018, 04:48:05 PM »
Not looking for actual position but rather how people word or interpret X" below the collar
 Is it
That rug really tied the room together, did it not?

Offline GKitson

  • Hero Member
  • *****
  • Posts: 720
  • Just another t-shirt guy
Re: Distance of Print Below Collar
« Reply #3 on: February 22, 2018, 04:51:30 PM »
Change wording to "below collar seam"

For example "top of image 3" below collar seam".  works on either front or back.
Greg Kitson
Mind's Eye Graphics Inc.
260-724-2050

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4232
Re: Distance of Print Below Collar
« Reply #4 on: February 22, 2018, 05:06:56 PM »
I don't think anybody ever reads it though.

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13945
  • Docendo discimus
Re: Distance of Print Below Collar
« Reply #5 on: February 22, 2018, 05:14:34 PM »
Kinda' my point.  I say (and use the)  "opening" Greg says (and uses the) "seam" We probably adjust for that inch or so difference.
My problem is those folks who expect us to read their minds. Folks like the LAPD who require their cadets to have a T and a Crew sweat with their names 2" tall, and 6" below the collar!
btw, over the years,  my clients have never had a problem with my position.
That rug really tied the room together, did it not?

Offline ebscreen

  • !!!
  • Gonzo Member
  • ******
  • Posts: 4232
Re: Distance of Print Below Collar
« Reply #6 on: February 22, 2018, 05:17:44 PM »
Kinda' my point.  I say (and use the)  "opening" Greg says (and uses the) "seam" We probably adjust for that inch or so difference.
My problem is those folks who expect us to read their minds. Folks like the LAPD who require their cadets to have a T and a Crew sweat with their names 2" tall, and 6" below the collar!
btw, over the years,  my clients have never had a problem with my position.

What if you are printing a girls shirt with a collar that's 1/4" tall and then a mens Beefy with the 1" tall neck wringer?

Offline mooseman

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2215
Re: Distance of Print Below Collar
« Reply #7 on: February 22, 2018, 06:20:03 PM »
We use the seam and go from there.
mooseman
DUE TO CIRCUMSTANCES COMPLETELY WITHIN MY CONTROL YOU SHOULD GET YOUR OWN TEE SHIRT AND A SHARPIE MARKER BY NOON TOMORROW OR SIMPLY CALL SOMEONE WHO GIVES A SHIRT.

Offline Frog

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 13945
  • Docendo discimus
Re: Distance of Print Below Collar
« Reply #8 on: February 22, 2018, 06:35:10 PM »
Kinda' my point.  I say (and use the)  "opening" Greg says (and uses the) "seam" We probably adjust for that inch or so difference.
My problem is those folks who expect us to read their minds. Folks like the LAPD who require their cadets to have a T and a Crew sweat with their names 2" tall, and 6" below the collar!
btw, over the years,  my clients have never had a problem with my position.

What if you are printing a girls shirt with a collar that's 1/4" tall and then a mens Beefy with the 1" tall neck wringer?


Always from opening (lining up with marks on the board, remember I started "pre-laser).  I always cheat 1/2" for the slightly lower collar and smaller size of standard crew ladies. Deep scoops and V's I have to determine the equivalent position, or, often, jam the image up as high as it will go!
That rug really tied the room together, did it not?

Offline Biverson

  • Full Member
  • ***
  • Posts: 180
Re: Distance of Print Below Collar
« Reply #9 on: February 22, 2018, 07:01:59 PM »
I've also measured from the seem. I've had to clarify with my employee between top of "collar" and "seam." Example: Line the art up 4 inches down from the top of the pallet, and then put the collar at the edge of the pallet, so the art is 3" down from the seam.
Brett - Pioneer Print Co.
www.idoshirts.com

Offline CBCB

  • !!!
  • Sr. Member
  • ****
  • Posts: 467
Re: Distance of Print Below Collar
« Reply #10 on: February 22, 2018, 09:28:29 PM »
We use the seam. Transfers over to sleeves as well. Always say “7cm down from the collar seam” or “2cm up from the left wrist seam” on a long sleeve for example.


Sent from my iPhone using Tapatalk

Offline Maxie

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1312
Re: Distance of Print Below Collar
« Reply #11 on: February 23, 2018, 09:06:38 AM »
I prefer the top of the collar, we have shirts with a rib from 1/2-1 inch.     Also when we position the shirt on the board we either mark the board or use a lazer, I think it’s easier to position on the edge of the collar and not on the seam.
Maxie Garb.
T Max Designs.
Silk Screen Printers
www.tmax.co.il

Offline johnny

  • !!!
  • Verified/Junior
  • **
  • Posts: 18
Re: Distance of Print Below Collar
« Reply #12 on: February 23, 2018, 11:50:00 AM »
i've always done from the seam

Offline Logowear

  • Verified/Junior
  • **
  • Posts: 51
Re: Distance of Print Below Collar
« Reply #13 on: February 23, 2018, 01:14:10 PM »
Seam, we position the seam just off the pallet so we don't have the collar on the pallet.
Specialty Stitches

Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6035
Re: Distance of Print Below Collar
« Reply #14 on: February 23, 2018, 05:21:03 PM »
We use the seam for reference as a rule, but any point of reference is fine as long as us and the customer are using the same point. We are around 3" down on a crewneck, but it really depends on the design, some things just need to be "eyeballed"...

Steve
I made a mistake once; I thought I was wrong about something; I wasn't