Author Topic: Index separated discharge  (Read 1895 times)

Offline Pangea

  • !!!
  • Full Member
  • ***
  • Posts: 228
  • Jack of all trades, master of none.
Index separated discharge
« on: February 22, 2019, 10:51:00 AM »
I'll be printing my first index separation with discharge next week and wanted to get an idea on mesh count to use? My feeling is 230 to make sure there's proper ink saturation but 305 to hit all the details. Any help would be appreciated!


Offline ericheartsu

  • Gonzo Member
  • ******
  • Posts: 3522
Re: Index separated discharge
« Reply #1 on: February 22, 2019, 11:43:03 AM »
I'll be printing my first index separation with discharge next week and wanted to get an idea on mesh count to use? My feeling is 230 to make sure there's proper ink saturation but 305 to hit all the details. Any help would be appreciated!

What DC are you using?
Night Owls
Waterbased screen printing and promo products.
www.nightowlsprint.com 281.741.7285

Offline BP

  • Sr. Member
  • ****
  • Posts: 380
Re: Index separated discharge
« Reply #2 on: February 22, 2019, 11:46:34 AM »
What LPI are you planning to run? That will tell you what mesh to use.
SHIRT HAPPENS!

Offline Pangea

  • !!!
  • Full Member
  • ***
  • Posts: 228
  • Jack of all trades, master of none.
Re: Index separated discharge
« Reply #3 on: February 22, 2019, 12:02:15 PM »

Offline ericheartsu

  • Gonzo Member
  • ******
  • Posts: 3522
Re: Index separated discharge
« Reply #4 on: February 22, 2019, 12:03:35 PM »
What DC are you using?

CCI

Personally i think 305 will be to high for that CCI. 230 might work ok?
Night Owls
Waterbased screen printing and promo products.
www.nightowlsprint.com 281.741.7285

Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6035
Re: Index separated discharge
« Reply #5 on: February 22, 2019, 12:27:48 PM »
What LPI are you planning to run? That will tell you what mesh to use.

Since indexing doesn't use lines per inch, what is your resolution? in pixels per inch? That will determine your grain size, which should help you determine your mesh. For instance, 100 ppi is 100 little square dots per inch, so 200 ppi is 200 littler (?) square dots per inch, half that size... I'm curious too, I haven't done an index sep in years, but usually 180 - 200 ppi.

Steve
I made a mistake once; I thought I was wrong about something; I wasn't

Offline brandon

  • Gonzo Member
  • ******
  • Posts: 1698
Re: Index separated discharge
« Reply #6 on: February 22, 2019, 12:37:15 PM »
We do discharge index with CCI. 225 and 300s will be fine

Offline Colin

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1610
  • Ink and Chemical Product Manager
Re: Index separated discharge
« Reply #7 on: February 22, 2019, 06:44:26 PM »
I would assume very very little dot gain with DC.  Make sure your reg is tight!
Been in the industry since 1996.  5+ years with QCM Inks.  Been a part of shops of all sizes and abilities both as a printer and as an Artist/separator.  I am now the Ink and Chemical Product Manager at Ryonet.

Offline brandon

  • Gonzo Member
  • ******
  • Posts: 1698
Re: Index separated discharge
« Reply #8 on: February 22, 2019, 08:09:35 PM »
I would assume very very little dot gain with DC.  Make sure your reg is tight!

Very true

Offline Pangea

  • !!!
  • Full Member
  • ***
  • Posts: 228
  • Jack of all trades, master of none.
Re: Index separated discharge
« Reply #9 on: February 23, 2019, 10:12:43 AM »
I separated at 200 DPI, I'll give the 230s a try. Thanks guys!

Offline Dottonedan

  • Administrator
  • Ludicrous Speed Member
  • *****
  • Posts: 5875
  • Email me at art@designsbydottone.com
Re: Index separated discharge
« Reply #10 on: February 24, 2019, 04:16:34 PM »
I separated at 200 DPI, I'll give the 230s a try. Thanks guys!


A word of caution:


Try to avoid having your resolution so close to your mesh. For example DO NOT use 200 resolution on a 200 mesh. Avoid anything close to that scenario. Go up higher to a 255m 280m, or 300m. If you have none higher, then you will need to accommodate that 200 mesh and drop the rez...for a slightly larger dot (square) such as a 170-180 rez. I think in your case, doing 200 and a 230 mesh... being 30 away either higher or lower, will be a safe.


Reason being, as the rez gets close to the mesh count number, you begin to get strong mesh interference. There is a name for it that is different than Moire, but You will see what looks like moire, (in the stencil) and thus into the print. HORRIBLE when this happens. You get a big ole rainbow looking thing in your print.


170 on 200 mesh
200 on 230 mesh
233 on 305 mesh
266 on 355 mesh


The cool thing about this indexing or stochastic, is that you can utilize various size (resolUtions in your file), to take advantage of gradations and textures etc. (in special effect inks) that are in your sim process.
Say your sim process is at 233 rez but you also have 2 stacked layers of puff ink for a more 3D look...and that puff ink has breakups or fades. Dimples for example. You can do all of this one in one file.
Artist & Sim Process separator, Co owner of The Shirt Board, Past M&R Digital tech installer for I-Image machines. Over 28 yrs in the apparel industry. Apparel sales, http://www.designsbydottone.com  e-mail art@designsbydottone.com 615-821-7850

Online tonypep

  • Ludicrous Speed Member
  • *******
  • Posts: 5610
Re: Index separated discharge
« Reply #11 on: February 25, 2019, 11:11:14 AM »
Mesh interference is what you want to avoid as Dan has mentioned. Depending on climate and shop (and ink systems), some lubricant and penetrant can help and prevent premature drying in the screen. CTS and Triloc (or other pre-reg systems) obviously speeds things up by a lot.

Offline Pangea

  • !!!
  • Full Member
  • ***
  • Posts: 228
  • Jack of all trades, master of none.
Re: Index separated discharge
« Reply #12 on: March 13, 2019, 05:14:03 PM »
Wanted to update and thank everyone. I was super nervous to print this but it ended up coming out great!