Author Topic: WHAT EMULSION ARE YOU USING?  (Read 4139 times)

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: WHAT EMULSION ARE YOU USING?
« Reply #15 on: May 14, 2019, 12:57:25 PM »
Ulano Orange has been what I use most consistently. Only down side is my films like to stick to it when it gets warmer out. I tried some cordless dehumidifier in the screen room last week and it's cut down on the tackiness but still get the occasional trashed film on the lower S-Threads

That is a very high solids emulsion. I could just never really get the resolution I needed with it. Chroma blue is alternative to the ulano orange.
Specializing in shop assessment's, flow and efficiency


Offline BP

  • Sr. Member
  • ****
  • Posts: 380
Re: WHAT EMULSION ARE YOU USING?
« Reply #16 on: May 14, 2019, 01:50:49 PM »
Rick, maybe your times are off a bit? I have be using Orange for years because of the EOM. We do a lot of sim process at 75 LPI/300-S mesh.

Remember that single cure emulsion not the best for fine resolution but can work if you exposure time are spot on.
« Last Edit: May 14, 2019, 01:53:16 PM by BP »
SHIRT HAPPENS!

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: WHAT EMULSION ARE YOU USING?
« Reply #17 on: May 14, 2019, 01:58:35 PM »
Rick, maybe your times are off a bit? I have be using Orange for years because of the EOM. We do a lot of sim process at 75 LPI/300-S mesh.

Remember that single cure emulsion not the best for fine resolution but can work if you exposure time are spot on.
[/quote

You know you may be right. we didn't test that one this round.. Thanks for pointing that out I will get some today and let the ladies give it a whirl,
Specializing in shop assessment's, flow and efficiency

Offline Nation03

  • Gonzo Member
  • ******
  • Posts: 1244
  • The Dude abides.
Re: WHAT EMULSION ARE YOU USING?
« Reply #18 on: May 14, 2019, 08:54:33 PM »
I've get some pretty great detail with the Orange which is why I keep coming back to it. I was using an Amergraph 150 for years before it crapped out and it was a great combo. Now I'm on my backup UV unit and the detail isn't quite as good but still not bad for Florescent bulbs.

Offline mooseman

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2215
Re: WHAT EMULSION ARE YOU USING?
« Reply #19 on: May 16, 2019, 09:31:54 AM »
Ulano Orange has been what I use most consistently. Only down side is my films like to stick to it when it gets warmer out. I tried some cordless dehumidifier in the screen room last week and it's cut down on the tackiness but still get the occasional trashed film on the lower S-Threads

That is a constant problem with orange and waterproof film. We solve that by simply dusting the screen wit baby powder. Be sure to use the cheaper talc as the corn starch better quality powder will only make the condition worse.
mooseman
DUE TO CIRCUMSTANCES COMPLETELY WITHIN MY CONTROL YOU SHOULD GET YOUR OWN TEE SHIRT AND A SHARPIE MARKER BY NOON TOMORROW OR SIMPLY CALL SOMEONE WHO GIVES A SHIRT.

Online Atownsend

  • !!!
  • Sr. Member
  • ****
  • Posts: 389
Re: WHAT EMULSION ARE YOU USING?
« Reply #20 on: May 16, 2019, 09:55:00 AM »
Baby powder worked for us. Since we switched to the Olec and vacuum frame we haven't had the need regardless of humidity. Not having heat on the glass from an enclosed unit is great. That exposure setup is still one of the best things i've ever bought. Running about 4 -5 gallons of ulna orange / month. About 100 screens / gallon according to latest data. We do mostly spot, so I like the high solids. Hard to coat thin on 280/35s but we still manage to hold pretty decent dots @ 55 LPI. Anyone ever mix in diazo with the Orange for better res?


Offline 3Deep

  • !!!
  • Ludicrous Speed Member
  • *******
  • Posts: 5243
Re: WHAT EMULSION ARE YOU USING?
« Reply #21 on: May 16, 2019, 10:18:44 AM »
Homer got me hooked on HXT and I've been using it now for years, if not HXT my next would be a dual cure Imagemate 521, that stuff is pretty good, just burn times are a little longer but well worth it.   
« Last Edit: May 16, 2019, 01:41:42 PM by 3Deep »
Life is like Kool-Aid, gotta add sugar/hardwork to make it sweet!!

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: WHAT EMULSION ARE YOU USING?
« Reply #22 on: May 16, 2019, 10:44:18 AM »
Homer got me hooked on HXT and I've using it now for years, if not HXT my next would be a dual cure Imagemate 521, that stuff is pretty good, just burn times are a little longer but well worth it.
[/quote

Actually the image mate 521 is the predecessor of the DTS Z1. Chromaline does still make it but the formulation of the z1 was made considering the LED units . The 2 products are very very similar.
Specializing in shop assessment's, flow and efficiency

Offline tonypep

  • Ludicrous Speed Member
  • *******
  • Posts: 5610
Re: WHAT EMULSION ARE YOU USING?
« Reply #23 on: May 16, 2019, 10:54:15 AM »
Chroma blue is a great emulsion if you are DTS/LED. Holds more detail than you can imagine and exposes in two to three seconds

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: WHAT EMULSION ARE YOU USING?
« Reply #24 on: May 16, 2019, 11:52:30 AM »
Chroma blue is a great emulsion if you are DTS/LED. Holds more detail than you can imagine and exposes in two to three seconds

YEA,TP we tested it and I have used many many gallons of chroma blue. Unfortunatly it's not even in the ball game with the Z1 as far as resolution on the higher end graphics. Chroma blue is a super overall emulsion though
Specializing in shop assessment's, flow and efficiency

Offline DannyGruninger

  • Gonzo Member
  • ******
  • Posts: 1220
Re: WHAT EMULSION ARE YOU USING?
« Reply #25 on: May 16, 2019, 03:20:06 PM »
We use murakami t9 here w/ diazo........ We've been doing some 7500 + pcs runs and no breakdown. All we run is wb here about 95% hsa

Danny Gruninger
Denver Print House / Lakewood Colorado
https://www.instagram.com/denverprinthouse

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: WHAT EMULSION ARE YOU USING?
« Reply #26 on: May 17, 2019, 02:54:29 PM »
We use murakami t9 here w/ diazo........ We've been doing some 7500 + pcs runs and no breakdown. All we run is wb here about 95% hsa

wow  I will sample that one. It has been mentioned by others also
Specializing in shop assessment's, flow and efficiency

Offline Colin

  • !!!
  • Gonzo Member
  • ******
  • Posts: 1610
  • Ink and Chemical Product Manager
Re: WHAT EMULSION ARE YOU USING?
« Reply #27 on: May 17, 2019, 07:44:18 PM »
Rick,

The addition of Diazo to any water resistant emulsion like T9 (which I love btw) or PHU and all its variants is what helps to give it that massive longevity.

In addition Danny has so many of his processes, especially the dark room, down to an absolute science.

Making sure everything is done properly and correctly up front the first time, your stencil durability increases tremendously.
Been in the industry since 1996.  5+ years with QCM Inks.  Been a part of shops of all sizes and abilities both as a printer and as an Artist/separator.  I am now the Ink and Chemical Product Manager at Ryonet.

Offline CBCB

  • !!!
  • Sr. Member
  • ****
  • Posts: 467
Re: WHAT EMULSION ARE YOU USING?
« Reply #28 on: May 20, 2019, 08:46:20 AM »
Rick,

The addition of Diazo to any water resistant emulsion like T9 (which I love btw) or PHU and all its variants is what helps to give it that massive longevity.

In addition Danny has so many of his processes, especially the dark room, down to an absolute science.

Making sure everything is done properly and correctly up front the first time, your stencil durability increases tremendously.

This is how I understand it as well!

We are just about to switch from Ulano Orange to PHU+Diazo.

Why PHU? It’s freeze stable and we’re in Canada. Distribution seems better for us than MURAKAMI, and we have a Saati LED bulb in our ryonet exposure unit. So I think it’ll be a good fit.

Hoping to get our resolution up and to play with some more ink types.


Sent from my iPhone using Tapatalk

Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: WHAT EMULSION ARE YOU USING?
« Reply #29 on: May 20, 2019, 09:50:43 AM »
Rick,

The addition of Diazo to any water resistant emulsion like T9 (which I love btw) or PHU and all its variants is what helps to give it that massive longevity.

In addition Danny has so many of his processes, especially the dark room, down to an absolute science.

Making sure everything is done properly and correctly up front the first time, your stencil durability increases tremendously.
[/quote

Yea, I am aware of that and do like the dual cures and have used them for a long time. We are just testing to get the same resolution with shorter exposure times. The longevity on water base runs is not as critical at this point. We also have a pretty tight Pre press set-up but with 16 staff artists and a lot of different separation techniques we are just testing all options.
Specializing in shop assessment's, flow and efficiency