Author Topic: HotHead, RoqIron temp setting  (Read 1644 times)

Offline chubsetc

  • Full Member
  • ***
  • Posts: 228
HotHead, RoqIron temp setting
« on: June 13, 2019, 07:50:16 AM »
I have had a HotHead for a couple months and I’m trying to get my temps right.  I am using Quick White and having issues with the ink sticking to the Teflon (M&R Teflon sheet connected to the 2 80/20 bars).  I’ve played with both flash temps before the iron and then the iron temp.  Below about 315 degrees it doesn’t smooth the base as well but also doesn’t stick.  Above 315 I start getting the sticking of the Teflon and some pull-up of the shirt from the pallet, specifically in areas with more solid ink deposits.  The base is incredibly smooth though above about 325 using a 225/48 screen for the base.  Any help would be appreciated.


Offline LuckyFlyinROUSH

  • !!!
  • Sr. Member
  • ****
  • Posts: 334
Re: HotHead, RoqIron temp setting
« Reply #1 on: June 13, 2019, 08:01:49 AM »
Hot head settings  - 390 deg - 40psi - quick stroke.

If it is sitting on the shirt for too long at too high of a temp it will peel white off

Make sure white base completely dry.
I spend too much money on equipment...

Offline BP

  • Sr. Member
  • ****
  • Posts: 380
Re: HotHead, RoqIron temp setting
« Reply #2 on: June 13, 2019, 08:31:37 AM »
We run at 380 deg. Spray a little silicon on the back of the teflon. If it sticks just speed the stroke up.
SHIRT HAPPENS!

Offline ffokazak

  • Sr. Member
  • ****
  • Posts: 403
Re: HotHead, RoqIron temp setting
« Reply #3 on: June 13, 2019, 01:38:38 PM »
damn y'all run them hot!

We run ours at 290, slow stroke.

Im going to try heating it up more!


Offline RICK STEFANICK

  • Gonzo Member
  • ******
  • Posts: 1925
  • INDUSTRY CONSULTANT-OPERATIONS SPECIALIST
Re: HotHead, RoqIron temp setting
« Reply #4 on: June 13, 2019, 03:43:27 PM »
BE sure the teflon in the sling is tight. We also run quick White
Specializing in shop assessment's, flow and efficiency

Offline jsheridan

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2130
Re: HotHead, RoqIron temp setting
« Reply #5 on: June 13, 2019, 05:41:35 PM »
BE sure the teflon in the sling is tight. We also run quick White

One of the newer guys was having some pickup today and couldn't' figure out why. turned out to be a loose Teflon screen. used it as a training session on how to troubleshoot the Teflon and how to tighten it.
Blacktop Graphics Screenprinting and Consulting Services

Offline chubsetc

  • Full Member
  • ***
  • Posts: 228
Re: HotHead, RoqIron temp setting
« Reply #6 on: June 14, 2019, 07:11:55 AM »
Thanks guys, we’ll play around and update!!

Offline IntegriTees

  • Full Member
  • ***
  • Posts: 178
Re: HotHead, RoqIron temp setting
« Reply #7 on: June 16, 2019, 02:43:58 PM »
wow, we're running the hot head at 350 at a slower speed.  I might try raising it with a faster stroke speed

I also tossed that sling out.  I could never get it to work and if you did have any sticking, it would start to pull the sling off the head clamp.
I went with a Shurloc EZ frame with their teflon panel.  That thing is tight and heavy duty.  works perfectly.

Offline Ross_S

  • Sr. Member
  • ****
  • Posts: 349
Re: HotHead, RoqIron temp setting
« Reply #8 on: June 17, 2019, 10:17:08 AM »
I thought you could run these as the first print?  In other words Iron the shirt prior to the base smoothing out any fibers there maybe and then you don't need to run a smoother.

Am I missing something I thought that was the better option than after the flash?

Ross

Offline LuckyFlyinROUSH

  • !!!
  • Sr. Member
  • ****
  • Posts: 334
Re: HotHead, RoqIron temp setting
« Reply #9 on: June 17, 2019, 12:11:31 PM »
You can use them as a first print, or a last print after flash. But the best way to matte down fibers we've found is to run it right after a flash on a base white.

Using it as a print first will still leave fibers sticking up.

Run your micros all the way in torwards the center of the press. Then lock in the sling pulling it tight as you lock it in, then start running your micros out so it tightens it up as much as possible.

I still do also like the teflon panel in a roller screen, but the teflon panel on a roller screen also tends to wear on corners of towels or other random items we print faster.


I spend too much money on equipment...

Offline Ross_S

  • Sr. Member
  • ****
  • Posts: 349
Re: HotHead, RoqIron temp setting
« Reply #10 on: June 18, 2019, 04:58:25 PM »
Interesting.  I've had a few reps try and talk me into it but I do really well with just a roller squeegee after the flash.  I haven't seen one in person in the last few years so I've got no hands on experience to say different.

Offline BP

  • Sr. Member
  • ****
  • Posts: 380
Re: HotHead, RoqIron temp setting
« Reply #11 on: June 19, 2019, 06:53:33 AM »
The hothead has 2 options. 1 is the hot iron and the other is a hot roller. I was told that the hot roller is for smoothing before the underbase. We just run the hot iron after the underbase and I will say I would not run a auto without one. It is a game changer for sure!
SHIRT HAPPENS!

Offline ffokazak

  • Sr. Member
  • ****
  • Posts: 403
Re: HotHead, RoqIron temp setting
« Reply #12 on: June 19, 2019, 01:21:13 PM »
We had a roller before, non heated.  ( Stadard action one or whatever)  Yes it worked pretty good.

The hot head is night and day. once you get it dialled you won't want to go back.

Smoothest whites in the game.


Offline im_mcguire

  • !!!
  • Hero Member
  • *****
  • Posts: 716
Re: HotHead, RoqIron temp setting
« Reply #13 on: June 19, 2019, 01:52:06 PM »
Can anyone confirm that these can be used with other presses maybe say a Workhorse? Or does it plug into the system of m&r, and it is proprietary.

Offline ffokazak

  • Sr. Member
  • ****
  • Posts: 403
Re: HotHead, RoqIron temp setting
« Reply #14 on: June 19, 2019, 05:48:42 PM »
Theres no speaking between the press and the hot head control.

You could put it on any press.

All controls are contained in the hot head box, so yeah I imagine it would work on any machine.