Recent Posts

Pages: 1 [2] 3 4 ... 10
11
General Discussion and ??? / Re: Comment, Like and Subscribe
« Last post by 3Deep on April 16, 2024, 02:30:49 PM »
Quote from: whitewater on April 16, 2024, 11:30:15 AM
Im in!

How far from Asheville NC are ya?

We are sitting here in lower Alabama (Dothan) what we call around here the Tri-states area, a stone toss from the Georgia, Florida Lines, if things work out we will be in Knoxville Tennessee June 8th for the 4th Annual Run to the hills ride.
12
General Screen Printing / Laminate over pallet tape?
« Last post by farmboygraphics on April 16, 2024, 01:53:03 PM »
This will probably only apply to the shops that also do signs in house, but has anyone ever tried putting laminate over the pallet (transfer) tape?
I'm not sure how well it would hold up to the flash or hold tack. Just a thought I had while printing some hoodies.  ;D
If I remember, I think I'll try it on one board next time I change tape.
13
General Discussion and ??? / Re: Comment, Like and Subscribe
« Last post by whitewater on April 16, 2024, 11:30:15 AM »
Im in!

How far from Asheville NC are ya?
14
General Discussion and ??? / Re: Comment, Like and Subscribe
« Last post by 3Deep on April 16, 2024, 09:23:31 AM »
Quote from: Homer on April 15, 2024, 09:01:26 PM
as long as you show me how to BBQ and make some of that shine, I'm all in buddy.

We just might run up on a BBQ and some shine but I don't think they will let me film it LOL
15
General Discussion and ??? / Re: Comment, Like and Subscribe
« Last post by Homer on April 15, 2024, 09:01:26 PM »
as long as you show me how to BBQ and make some of that shine, I'm all in buddy.
16
General Discussion and ??? / Comment, Like and Subscribe
« Last post by 3Deep on April 15, 2024, 05:16:21 PM »
Hey guys I just started my youtube channel (@southerboyzryde) and yep it's a little rough LOL, doing content is a little tougher than I thought it was going to be, but fun also, learning something new.  So if you like motorcycles, cars and want to ride with us around the south, subscribe to the channel leave a comment let me know what I need to work on Pros/Cons.
17
Equipment / Re: Work Horse Quartz conveyor dryers... worth it?
« Last post by spencer_L&KC on April 12, 2024, 04:24:01 PM »
Quote from: Evo on April 09, 2024, 05:53:55 PM
Quote from: spencer_L&KC on April 09, 2024, 03:07:56 PM
def want to go forced air as it is time to take WB ink seriously.

If you are upgrading and planning for growth and even *remotely* considering WB ink, get a gas dryer with the longest tunnel you can fit in that 1600 sq ft. Anything shorter than 12' and you will be pulling your hair out balancing proper cure and production speed. 16' is even better if you plan on an auto.

A decent condition used Sprint (or even a mini Sprint) will spank every electric dryer on the market.

thanks for the heads up! ill check them out.
18
General Art Discussions / Re: Very strange art issue
« Last post by Atownsend on April 12, 2024, 03:49:59 PM »
i guess it comes down to not understanding how the RIP is actually working.

Moral of the story... always make sure everything is converted to outlines. It just blows my mind that the raster data was changed from a vector font being present and not outlined.
19
General Art Discussions / Re: Very strange art issue
« Last post by Atownsend on April 12, 2024, 03:37:55 PM »
Quote from: zanegun08 on April 12, 2024, 03:05:02 PM
You know how you tell your customers to create outlines around their fonts?  Do the same thing.

Object < Flatten Transparency < Click Convert All Text To Outlines < OK.

Tried it, but to do that i need to embed the DCS 2 file, which AI wont allow.




The typeface in the art file that was affected is a raster. The placement label was not converted to an outline.

I manually converted the font and dropped it in the rip. What do you know... its spelled correctly. THANKS!! What is going on here? I get the effect, but im not understanding the cause.
20
General Art Discussions / Re: Very strange art issue
« Last post by zanegun08 on April 12, 2024, 03:05:02 PM »
You know how you tell your customers to create outlines around their fonts?  Do the same thing.

Object < Flatten Transparency < Click Convert All Text To Outlines < OK.
Pages: 1 [2] 3 4 ... 10