TSB
Computers and Software => Separation Programs => Topic started by: Dottonedan on December 07, 2014, 12:23:37 AM
-
I've tried on my own, and I've read other forums on the Epson, and have even downloaded the general Epson printer service manual but haven't found anything that specifically tells you how to remove the cover. You'd think I could find it on my own, but it's hidden somehow.
I'm thinking i need to soak the pads and maybe run some isopropyl thru the heads. Been sitting for a year or so.
-
Mine sat in a hot attic for 2 years and fired up and printed fine after 2 clean cycles. I'd fire it up and see how it goes, the things are tanks.
-
Oh, I've fired it up. It's printing (or going thru the motions) but not printing ink. No nozzle check images. I've done about 8 auto cleans. I might need to replace the ink cartridges also. Who knows. I just wanna get the cover off, so I can get inside and clean it. I can see a good bit of dust fuzz near heads.
-
https://archive.org/details/printermanual-epson-stylus-color-3000-service-manual
This has been the most helpful instructions I have found. Section 3.2 It is pretty easy after you do it one time
-
https://archive.org/details/printermanual-epson-stylus-color-3000-service-manual
This has been the most helpful instructions I have found. Section 3.2 It is pretty easy after you do it one time
Thank you for the link. I have 2 spare 3000's and have been wanting to go through them.
-
They come apart very easy you got four in the back, one where the ink carts go and I think two or three under the paper tray once you pull it out. then you need to take a flat head screw driver and push the tabs back on the under side of the printer to pull the top off, oh and don't forget to take off the control panel first and unplug it. Just be careful and don't break stuff or force it apart it comes apart very easy. I've taken two apart all the way down the motor in the back and replaced springs heads you name it, but getting the bastards primed back with ink is a mother good luck...
darryl
-
Thanks Guys. With that service manual, I'm in and cleaning. Thanks for the tips. Not all manuals go through everything I found out. This one is best. I've made this thread a sticky for others.
-
get some windex and soak a paper towel with it then park the heads on top of it. That should clear it . . .
pierre
-
That will work fine I'm sure. I'm out of windex, but have been able to get it to print a decent nozzle check and printed images. Just patiently cleaning and noz checks. Then printed a few large solid areas...and finally,printed some halftones. No rip yet. I wanted to use the one provided (supposed to be pretty good) but it only works on and older version of windows.
The thing I will be attacking now, is the rows of thing lines where the print doesn't seem to overlap enough. I've done some alignment test and narrows it down to what looks as good as can be done. Still, I have those lines going across horizontally. That has to be the spacing of when the first row of prints lay over the next. Seems to be a slight gap. I imagine possibly if I could change the amount ink laydown/slow the printer down that might overlap more.
I don't know much about the Epson 3000's so if anyone has any basics to toss in, feel free.
-
I don't know much about the Epson 3000's so if anyone has any basics to toss in, feel free.
I know that folks always used to ask what settings provided a good black positive. I assume those were folks without a third party rip.
In that situation, you want the settings for backlit films, though you, with your emphasis on halftones will surely be using a sophisticated rip at some point I bet.
-
dan, what version of windows are you on? I got it to run on 7...i think.
you have to run & install it in compatibility mode
-
get some windex and soak a paper towel with it then park the heads on top of it. That should clear it . . .
pierre
We do that when we have to, plus we also have a large syringe we fill with cleaning fluid that fits over the nipples that the ink carts sit on, then squeeze the fluid through onto the aforementioned paper towel. When it starts to run clear, you're pretty close to clean... haven't tried it on a 3000, but it works on the 1400 and the like...
Steve
-
dan, what version of windows are you on? I got it to run on 7...i think.
you have to run & install it in compatibility mode
Using windows 7. It's running, but I"ll need to fine tune it. Where or at what point to do you find the "compatibility" mode?
-
dan, what version of windows are you on? I got it to run on 7...i think.
you have to run & install it in compatibility mode
Using windows 7. It's running, but I"ll need to fine tune it. Where or at what point to do you find the "compatibility" mode?
I thought that that was an option offered up by Win 7 when installing a legacy driver
-
If so, I musta not needed it then, because I went to the Epson website and downloaded it's latest driver for my operating system and had no issues.
-
Well, Brad will clear that up tomorrow.
-
man dan. I might have to log into your system and mess around to get it to work. i am 99%certain I can. I will almost have to see it to remember though.
-
I'm fine with you logging in, but I'm still wondering for what? The printer is indeed working, just not 100% perfect yet. Are you talking about some different setting I can only get from a specific type of download to achieve the overlapped print steps so that there are no streaks across my images?
If so, I had been thinking that may change with a better choice of paper or film. I'm just printing in regular 8.5x11 printer paper till I get some film.
Oh, I get it. You're talking about a compatibility thing (for the RIP software). Oh, I see. Yes, YES, I want that.
-
Just bought a near-new 3000 for $100. Finally a back-up for mine. man I love buying new-to-me equipment.
-
What happen to the InkjetDoctor I tried a few times awhile back to get a printer from him and he had nothing....Homer hooked me up with another guy...
-
Just bought a near-new 3000 for $100. Finally a back-up for mine. man I love buying new-to-me equipment.
$100.00? Nice.
-
Yup, comes with all covers, the roll holder and full inks.
-
Awesome price. Nice snag!