Author Topic: Trouble reclaiming Murakami T9  (Read 6741 times)

Offline Raw Paw

  • Verified/Junior
  • **
  • Posts: 63
Trouble reclaiming Murakami T9
« on: March 23, 2022, 07:46:06 PM »
Hello warriors of the print realm.

Hopefully simple question here..  It just same to my attention our T9 is not reclaiming nice..  Rather than disolving into a nice lather after spraying on the emulsion remover and scrubbing, it is being blasted off in chunks.  The chunks are then clogging our drainage system.  No dip tank, manually reclaiming and spraying.

This is our emulsion remover - https://www.screenprintsupplies.com/products/cleaning-chemicals/printers-choice-screen-printing-chemicals/printers-choice-emulsion-remover-concentrate-130/

Are all emulsion removers more or less the same?  Should we use a specific one for PP emulsions?  I know underexposure can cause reclaim to be difficult, I was also made aware that having too strong of emulsion remover can be counter productive and cause this issue.  Any other variables to be aware of?

Thanks
Live by the blade, Die by the blade


Offline Sbrem

  • Ludicrous Speed Member
  • *******
  • Posts: 6055
Re: Trouble reclaiming Murakami T9
« Reply #1 on: March 24, 2022, 09:40:31 AM »
Scrubbing with emulsion remover and using the pressure washer immediately, as you've been doing, should be fine. If by chance though, it's allowed to sit for a while, I've seen problems where it's harder to reclaim. I don't think we've used T9 here (maybe experimented with it once) so this is kind of general as emulsion removing goes.

Steve
I made a mistake once; I thought I was wrong about something; I wasn't

Offline 3Deep

  • !!!
  • Ludicrous Speed Member
  • *******
  • Posts: 5325
Re: Trouble reclaiming Murakami T9
« Reply #2 on: March 24, 2022, 10:18:12 AM »
I run into this problem more than I like, I use two different emulsion brands and one reclaims very easy and the other blows out in chunks at times, I'm thinking the one that blows out in chunks has more solids in the mix than the other brand, we use the same emulsion remover for both.  Now I will say unlike you we don't scrub the screens, just spray let sit for a minute or so and blast away.
Life is like Kool-Aid, gotta add sugar/hardwork to make it sweet!!

Offline ericheartsu

  • Gonzo Member
  • ******
  • Posts: 3539
Re: Trouble reclaiming Murakami T9
« Reply #3 on: March 24, 2022, 11:20:28 AM »
have you reached out to murakami? I feel like they could probably give you better insight than anyone here. Unless there is a murakami specific shop on here.
Night Owls
Waterbased screen printing and promo products.
www.nightowlsprint.com 281.741.7285

Offline Doug S

  • Gonzo Member
  • ******
  • Posts: 1481
Re: Trouble reclaiming Murakami T9
« Reply #4 on: March 24, 2022, 11:57:45 AM »
I use the T9 here.  I have a dip tank though and never had that problem unless I'm reclaiming a 24 or 40 mesh.  There have been times that I've used straight genzyme emulsion remover when my tank chemical get weak.
It's not a job if you love doing it.

Offline Orion

  • !!!
  • Hero Member
  • *****
  • Posts: 764
  • Ain't no shortcuts in screen printing.
Re: Trouble reclaiming Murakami T9
« Reply #5 on: March 25, 2022, 03:30:13 PM »
Revisit your exposure times. Make sure you are getting complete exposure. Ensure that your screen-room is at an acceptable humidity level. The emulsion layer needs to be below a certain level of humidity to obtain proper exposure. Next, contact River City to check on shelf life of your emulsion remover and also if it is the best chioice for PP emulsions. Look at your on press wash or screen opener and also your ink remover/degradent. PP emulsions don't get along well with most solvents.
Dale Hoyal

Offline Rockers

  • !!!
  • Gonzo Member
  • ******
  • Posts: 2073
Re: Trouble reclaiming Murakami T9
« Reply #6 on: March 26, 2022, 02:49:22 AM »
Revisit your exposure times. Make sure you are getting complete exposure. Ensure that your screen-room is at an acceptable humidity level. The emulsion layer needs to be below a certain level of humidity to obtain proper exposure. Next, contact River City to check on shelf life of your emulsion remover and also if it is the best chioice for PP emulsions. Look at your on press wash or screen opener and also your ink remover/degradent. PP emulsions don't get along well with most solvents.
We are using T9 for many years now, never rally had the issue he is describing. And yes exposure times might the key. And like you said solvents. We use CCI Envirowipe. Works great for all PP emulsions unlike standard solvents and other cleaners.

Offline Raw Paw

  • Verified/Junior
  • **
  • Posts: 63
Re: Trouble reclaiming Murakami T9
« Reply #7 on: March 29, 2022, 03:30:24 PM »
Revisit your exposure times. Make sure you are getting complete exposure. Ensure that your screen-room is at an acceptable humidity level. The emulsion layer needs to be below a certain level of humidity to obtain proper exposure. Next, contact River City to check on shelf life of your emulsion remover and also if it is the best chioice for PP emulsions. Look at your on press wash or screen opener and also your ink remover/degradent. PP emulsions don't get along well with most solvents.
We are using T9 for many years now, never rally had the issue he is describing. And yes exposure times might the key. And like you said solvents. We use CCI Envirowipe. Works great for all PP emulsions unlike standard solvents and other cleaners.

We upgraded to a dip tank and the chemicals in it are handling T9 much better.  Will look into solvents if the problem persists, this is a great suggestion.  Thanks everyone!

Also I did reach out to Murakami to sort the issue, their representative was saying it wasn't the emulsion remover / they are all made the same, so I reached out here for some more clues.
Live by the blade, Die by the blade