TSB
screen printing => Equipment => Topic started by: Dottonedan on January 20, 2017, 01:51:50 PM
-
I need a few suggestions on where/who to get a couple things.
1, Thermocouple Donut.
2, Tension meter. Doesn't have to be to of the line.
3, Location that re-stretches static frames.
I've checked a couple places and are either way out of line on price or don't have it at all.
-
we use to use pocono mtn in PA for re stretching frames...there were the closest to us at the time. Look into buying new ones also. Might be cheaper than shipping back and forth.
I could also use a donut...I know a lot of people have purchased from here...https://www.instawares.com/screen-print-donut-surface.cak-50008k.0.7.htm (https://www.instawares.com/screen-print-donut-surface.cak-50008k.0.7.htm)
-
Spot Color re stretches for us. They use the red glue and its always a great job
-
Spot Color Supply is the BEST for restretch!
-
A note on the re-stretch. Especially with the new shipping standard of size trumping actual weight, I found it sometimes not a lot cheaper to re-stretch than buy whole new frames with shipping only one way, and often thrown in with a minimum purchase. Of course, this outgoing shipping cost can vary greatly with distance.
-
We've always stretched our own, but a few times it was extremely easy to just buy new ones stretched. Of course, when they get messed up, we have a vintage M&R Blue Max stretcher that does a good job for us, we like the red glue too, not as fast as instant, but lasts a lot longer.
Steve
-
Xenon restretches without using any kind of grinding process to remove the mesh and existing glue. Located just over the line in AR from Branson. If you get a donut, know that it is only 1 piece of the dryer mapping puzzle. This is a service I offer as I have a calibrated donut probe. You also need a non contact temp gun and heat strips. I am a proponent of dryer mapping at each change of seasons.
-
Is the ATKINS THERMOCOUPLE DONUT typically used for older more questionable dryers? We have a brand new one so should be good.
Seems to be difficult to locate a source that carries both the probe and reader.
Like this source, is jsut for the probe. https://www.instawares.com/screen-print-donut-surface.cak-50008k.0.7.htm (https://www.instawares.com/screen-print-donut-surface.cak-50008k.0.7.htm)
I can't see that they have the other.
-
Is the ATKINS THERMOCOUPLE DONUT typically used for older more questionable dryers? We have a brand new one so should be good.
Seems to be difficult to locate a source that carries both the probe and reader.
Like this source, is jsut for the probe. https://www.instawares.com/screen-print-donut-surface.cak-50008k.0.7.htm (https://www.instawares.com/screen-print-donut-surface.cak-50008k.0.7.htm)
I can't see that they have the other.
yep , that will work just fine or get a gun and hit the print exiting the dryer
-
Ryonet is coming out with new thinner screens with high end S mesh and higher tension. We have few coming in to test. If they work OK, they should be cheaper to ship and thus reduce the ownership cost. I have no idea on the pricing though and many other options listed here are good. I only bring it up as it might be an interesting concept (trying to save on the shipping).
pierre
-
I have an extra Newman meter that I'd sell for $100 plus shipping. Let me know.
-
Excited to get feedback on testing, thanks Pierre! One concern that we have is that they may be too thin for everyone's presses so that is one area of feedback we are looking for, also ink management, ensuring that they are not too thin for that. Weight and rigidity look good however.
Ryonet is coming out with new thinner screens with high end S mesh and higher tension. We have few coming in to test. If they work OK, they should be cheaper to ship and thus reduce the ownership cost. I have no idea on the pricing though and many other options listed here are good. I only bring it up as it might be an interesting concept (trying to save on the shipping).
pierre
-
Too thin? Is it equal to the LX type? The welded knuckle or just thinner thread? Please send some our way to test as we only use thin thread.
-
I have an extra Newman meter that I'd sell for $100 plus shipping. Let me know.
When was it calibrated last? I'm interested.
-
Too thin? Is it equal to the LX type? The welded knuckle or just thinner thread? Please send some our way to test as we only use thin thread.
too thin on the frame profile. They are half height. So 1.5" wide, but what seems to be only 1" or possibly 0.75" tall.
Mesh is standard S mesh from SAATI if I understand correctly. Ryan will know more.
pierre
-
Ah, I misread. To thin on the frame. Gotcha.