TSB
screen printing => Tips and Tricks to Share (Please don't ask questions here) => Topic started by: screenprintguy on November 28, 2012, 02:08:50 PM
-
Check out this pic. I found a 42" wide broan range hood that fits and works perfect on the catch side of our heat wave 36" dryer. It has a built in fan and light with 8" exhaust port on the top to attach pipe or hose. It's light enough that I took the exit door of the dryer off, flipped it over, and attached the hood to that door so that we didn't have to peirce the outter layer of the dryer. It looks like it's going to work perfect for catching smoke. $69 with free shipping, not to shabby!
(http://i47.tinypic.com/2ly0iep.jpg)
-
That's a great deal. I have something similar and paid the manufacture $250 for it. It doesn't have a light or fan. The light would be cool.
Can you post here you got it?
-
I almost had a sheet metal shop make one custom and it was going to be almost 300 plus fan ect. Now i know the fan in it might not be the best and last that long, but then again it's made to suck air over a stove with steam and grease and those tend to hang in there for a while. So we will see how long that lasts. I have a few inline duct fans sitting around so if and when the fan goes. I'll yank it out and put an inline fan down the line somewhere, but all and all, I thought it was a good deal. Hope it can help others out looking to catch stank smoke from their catcher end.
-
I just had a inline fan go bad this last week. The lint just destroys them. Mine was rated for 250 CFM. It did a ok job. I have a 750 CFM on on order. More power!
-
you totally stole my patent pending idea... :) Im going to do that to both ends of my dryer.
-
I told I think Shawn about doing that years ago on his old dryer, you might even want to install an extra fan...oven hoods work great for that, lol but I think thats what they were meant for for anyway.
Darryl
-
is it used at 69 clams?
-
My bad, I checked the invoice, it was actually $63 after shipping, so $63 total, got it in 4 days.
Screengear--- I am going to use the grease filter that is in it and put a piece of cut t-shirt material over it to change every so often, we do that on all of our fan intakes on equipment, keeps the dust out and allows the air to flow with no prob.
3Deep---- adding a fan down the line is probably a good idea, better to have more flow and catch all that stank smoke from discharge prints. Here is a link direct to the place we got it from.
http://www.ventingdirect.com/broan-4242d-42-under-cabinet-range-hood-with-damper-included/p1025285?source=trm_OrderConfirmation_VentingDirect.com_p1025285 (http://www.ventingdirect.com/broan-4242d-42-under-cabinet-range-hood-with-damper-included/p1025285?source=trm_OrderConfirmation_VentingDirect.com_p1025285)
-
Screengear--- I am going to use the grease filter that is in it and put a piece of cut t-shirt material over it to change every so often, we do that on all of our fan intakes on equipment, keeps the dust out and allows the air to flow with no prob.
I will have to look into a filter for my next one. Even a simple house Hvac filter from Home depot would work to keep the lint out of the fan.
-
Just wanted to share this inline fan off amazon. $84.99 shipped for 720 CFM
http://www.amazon.com/Output-In-line-Exhaust-Scrubber-Filter/dp/B004OH0DIE/ref=pd_vtp_lg_7 (http://www.amazon.com/Output-In-line-Exhaust-Scrubber-Filter/dp/B004OH0DIE/ref=pd_vtp_lg_7)
-
Just wanted to share this inline fan off amazon. $84.99 shipped for 720 CFM
[url]http://www.amazon.com/Output-In-line-Exhaust-Scrubber-Filter/dp/B004OH0DIE/ref=pd_vtp_lg_7[/url] ([url]http://www.amazon.com/Output-In-line-Exhaust-Scrubber-Filter/dp/B004OH0DIE/ref=pd_vtp_lg_7[/url])
Oh yeah those are nice we have 1 of those in the back on our washout booth to exhaust fumes when re claiming they are really really powerful great fan
-
Remember that when you add a fan, or increase the size of an existing one, you can reduce the dryer heat, necessitating a re-evaluation of your usual cure temps and times.
This will probably be more apparent on Electric only dryers.
-
Trust me Frog, if I can get a little extra heat pulled out when we slow our belt down to 1.5 to do discharge printing, we will be better off. Our dryer tends to climb to 400 when we slow our belt down below 2 if shirts stop running through. If we keep a steady flow of shirts, it holds with no problem at that slow speed, if we have an empty dryer belt it climbs at that slow speed, so a little extra sip might actually help that issue.